-
This is my xs650 bobber i have been buildin it and have no time for it anymore. The only thing left to do is to run the wires an it is ready to ride. I have lost interest in the bike and just wanna get rid of it. Hit me up with any offers and reme...4 weeks ago on MautofiedTools
-
This is a 1980 Sporty HD 1000. forward controls I am 6,2 and 215 It feel great for my size and my smaller buddys. The engine was just completely redone from top to bottom. It has been MAUTOFIED to a hardtail. it sounds great with the drag pipes. I...4 weeks ago on MautofiedTools
-
Older bike very rare in this condition. DOES NOT RUN. I think its a spark issue. It turns but never starts so its getting fuel and air. Its just been too cold to work on it. 2 brand new tires. New starter, kickstand, from pegs. Comes with a wind g...4 weeks ago on MautofiedTools
-
1982 KZ 1000P ON A AMEN SAVIOR FRAME, DOUBLE SPRING GIRTER FRONT END, CUSTOM TANK AND LEATHER WORK, BIKE RUNS AND RIDES STRONG, CARBS PROBABLY NEED TO BE CLEANED, CLEAN TITLE, OPEN TO TRADES AS LONG AS ITS STREET LEGAL OR GUNS WITH BOOT, TEXT OR C...4 weeks ago on MautofiedTools
-
ROLLER ONLYit sit as a roller right nowhard tail frame pretty good rakeold school chrome long springer front end paughcoI have the engine pulled out and most of the bike apart, its sits as a roller right now, no tank. But theexhaust can go with it...4 weeks ago on MautofiedTools
-
this is a 1981 Yamaha Xs650, there is nothing factory about this bike beside the motor and is been touched. its been on the street one time since finished,and hadnt even warn the nipples off the tires.newHarley springer front endheadlight/turnsign...4 weeks ago on MautofiedTools
-
Every nut and bolt is new stainelssEverything newtirestubesHeritage softail 16 inch rimssprocketsrotorschainFab Kevin dual piston caliperscablesbrake linesrear master cylinderArlen Ness dashmooneyes seatspeedometerwiringAndrews camS&S cam coverS&S...4 weeks ago on MautofiedTools
-
… . The car has a custom motion paint scheme and was painted about one year ago. It has a 350 motor with a five speed transmission. It runs well and is very reliable. It has a custom interior and brand-new seat covers. It has pow...Over 4 weeks ago on ClazTools
-
I did get it started in Dec. has to have choke half open to idle. it is complete, but needs a few new parts. located in Rochester. great project.Over 4 weeks ago on ClazTools
-
1982 t-craft with TRAILER 6500 with a 1998 200 Johnson outboard motor that runs the boat is in good condition was redone 5 years ago in Miami with new wiring new fuel lines sanded down hull and new paint and new bottom paint has new gauges and ,li...Over 4 weeks ago on ClazTools
-
416th One Ever Built9/72 Build Date Clean Title1973 Kawasaki Z1 900 Motorcycle, all original bike, 28373 miles, runs drives as it should, newer battery, good tires, 3 original keys, original manual, original tool kit, has some patina, some rear ri...Over 4 weeks ago on ListedBuyTools
-
1950 Harley Davidson WL 45ci Flathead in Red paint. Bike in the 1970's was restored/rebuilt. Bike is in good condition and runs and operates as it should. Bike is hand shift 3 speed, foot clutch, kick start, 6 volt. Bike is all Harley Parts and ta...Over 4 weeks ago on ListedBuyTools
-
1950 Harley Davidson EL Panhead. Its in the original wishbone frame, original tins, wheels, front end.ect. Has a clean and clean VIN and belly numbers do match. This is a very original bike. Has a M35 Carb. That is the original Speedometer for the...Over 4 weeks ago on ListedBuyTools
-
416th One Ever Built 9/72 Build Date Clean Title 1973 Kawasaki Z1 900 Motorcycle, all original bike, 28373 miles, runs drives as it should, newer battery, good tires, 3 original keys, original manual, original tool kit, has some patina, some rear ...Over 4 weeks ago on Yupyi!Tools
-
1950 Harley Davidson WL 45ci Flathead in Red paint. Bike in the 1970's was restored/rebuilt . Bike is in good condition and runs and operates as it should. Bike is hand shift 3 speed, foot clutch, kick start, 6 volt. Bike is all Harley Parts and t...Over 4 weeks ago on Yupyi!Tools
